Custom Dove prisms

Dove Prisms for Image Rotation, Made in Rye

Kingsview Optical makes custom Dove prisms to your drawing for image rotation in imaging, scanning and beam rotation systems. We polish the long base and the angled ends, coat the end faces and measure every prism at our site in Rye, East Sussex.

  • Made in Rye, East Sussex
  • Image rotation and inversion
  • Coated in-house
  • ISO 9001:2015
Custom Dove prisms made by Kingsview Optical in Rye, UK
Dove prisms, polished in Rye.
Prisms made here, start to finish. Shaped, polished, coated, cemented and measured at our site in Rye.
See how we make them →
The basics

What a Dove Prism Does

In short: a Dove prism is a right angle prism with its corner cut off, used along the optical axis. Light enters one sloped end, reflects once off the long base and leaves the other end in line with where it came in, with the image inverted. Rotate the prism by an angle and the image rotates by twice that angle.

Because the beam leaves on the same axis it entered, a Dove prism can sit in a straight optical path. Turning it about that axis rotates the image, which is why Dove prisms are used as image rotators in scanning, tracking and inspection systems.

The reflection off the base is total internal reflection, so no mirror coating is needed there. We AR-coat the two end faces for your wavelength.

Dove prisms work best in collimated light. In a converging beam, the tilted end faces add astigmatism. Dove prisms are also long relative to their aperture, so tell us the clear aperture you need and we'll size the prism and its length to suit your glass and wavelength.

Dove prism: the beam reflects once off the base and leaves on the same axis.
Prism rotated 0°FImage invertedPrism rotated 45°FImage turns 90°
Rotating the prism by 45° rotates the image by 90°.
Applications

Where Our Dove Prisms Are Used

Image rotationRotating an image in scanning, tracking and inspection systems.
Beam rotationRotating a laser beam profile or the orientation of a pattern.
InterferometryInverting or rotating one arm of an interferometer.
Machine visionRe-orienting an image without moving the camera.
Periscopes and sightsCorrecting image orientation in a straight optical path.
Research opticsBeam and image manipulation in laboratory set-ups.
Specification

Dove Prism Specification

These are our standard tolerances. If your design needs tighter, tell us which parameter. We'll tell you plainly whether we can hold it, and what it adds to cost.

Size range0.8mm micro prisms to over 100mm
Dimension tolerance±0.1mm
Angle tolerance±3 arcmin standard, tighter on request
End face angles45° as standard, or to your design
Base reflectionTotal internal reflection, no coating needed
Flatnessλ/4 @ 633nm
Surface quality (scratch-dig)60/40 standard, 40/20 on request
MaterialsSchott, Ohara and CDGM optical glass; fused silica
CoatingsBroadband AR (standard 425 to 650nm, wider on request), wide-angle AR, V-coat, MgF2, custom designs on the end faces
FinishingBlackened edges, protective chamfers, steps, bevels, drilled holes

Not sure what to specify? Tell us the clear aperture, the wavelength and whether the beam is collimated. The length of a Dove prism follows from those, and we'll suggest a size that fits your system.

Options

Made to Fit Your System

Questions

Dove Prism Questions

How does a Dove prism rotate an image?
A Dove prism inverts the image along one axis. When you rotate the prism about the optical axis, that axis of inversion rotates too, so the image rotates at twice the rate: turn the prism 45° and the image turns 90°.
Do Dove prisms need a mirror coating?
Not on the base. The beam reflects off the base by total internal reflection. The end faces need an AR coating to keep transmission high, which we apply in our own chambers.
Can I use a Dove prism in a converging beam?
It is best in collimated light. In a converging or diverging beam, the tilted end faces add astigmatism. If your system can't provide collimated light, tell us and we'll talk through the options.
Why are Dove prisms so long?
The beam has to travel along the prism and reflect off the base, so the length is several times the aperture. The exact ratio depends on the glass and the end angles. Tell us the clear aperture and we'll calculate the length.
Does a Dove prism change the direction of the beam?
No. The beam leaves on the same axis it entered, which is what lets a Dove prism sit in a straight optical path.
What do you need to quote a Dove prism?
A drawing with the length, height, width and end angles, or the clear aperture and wavelength if you need us to size it, plus the glass, coatings and quantities.

Other Prisms We Manufacture

Or see our full optical prism manufacturing capability, and our optical design service if you need help choosing or designing a prism.

Getting a Quote for Dove Prisms

Send us your prism drawing. An engineer from the team that would make your prisms, not a sales team, will review it. They'll tell you plainly what's achievable and what will drive cost.

What to send

  • Drawing (PDF or ISO 10110) with dimensions and angles
  • Glass type, or the wavelength range if you're not sure
  • Clear aperture, or length, height and end angles
  • AR coating and wavelength range
  • Quantities: prototypes and expected production volumes

What happens next

  1. An engineer reviews itWithin one working day, flagging anything that will drive cost or lead time.
  2. We quote the prismFor the prototype, and for production at your volumes.
  3. We make, measure and deliverAll in Rye, with inspection data if you need it.

Need a Custom Dove Prism?

Send your drawing, or describe what the prism needs to do. We'll tell you plainly how we'd make it, what it will cost and how long it will take.

Made in Rye, East Sussex. NDA-friendly. Defence and security work welcome. ISO 9001:2015.